Deutsch
Das keilförmige Durchgangsfutter entspricht den japanischen und taiwanesischen Standards.
Alle Gleitflächen sind gehärtet und präzise geschliffen.
| Spez | A | B | C | D | D1 | D2 | E | E1 | F | G1 | G2 | H | |
| KT05-3 | A4 | 135 | 60 | 110 | 82.6 | 63.51 | 96 | 4 | 20 | 36 | 1 | -10 | 20 |
| KT06-3 | A4 | 165 | 81 | 140 | 104.8 | 63.51 | 116 | 5 | 20 | 45 | 11 | -1 | 19 |
| KT06-3 | A5 | 165 | 81 | 140 | 104.8 | 82.56 | 116 | 5 | 15 | 45 | 11 | -1 | 19 |
| KT08-3 | A5 | 210 | 91 | 170 | 133.4 | 82.56 | 104.8 | 5 | 24 | 52 | 14.5 | -1.5 | 20.5 |
| KT08-3 | A6 | 210 | 91 | 170 | 133.4 | 106.38 | 150 | 5 | 17 | 52 | 14.5 | -1.5 | 20.5 |
| KT10-3 | A6 | 254 | 100 | 220 | 171.4 | 106.38 | 133.4 | 5 | 28 | 75 | 9 | -10 | 25 |
| KT10-3 | A8 | 254 | 100 | 220 | 171.4 | 139.72 | 190 | 5 | 18 | 75 | 9 | -10 | 25 |
| KT12-3 | A8 | 304 | 110 | 220 | 171.4 | 139.72 | 190 | 6 | 18 | 91 | 8 | -15 | 28 |
| KT15-3 | A8 | 381 | 133 | 300 | 235 | 139.72 | 171.4 | 6 | 33 | 118 | 11 | -16 | 43 |
| KT15-3 | A11 | 381 | 133 | 300 | 235 | 196.87 | 260 | 6 | 22 | 118 | 11 | -16 | 43 |
| Spez | Kmax. | L | L1 | M | N | P | S | T | U | X | Y | A1 | 4-M1 | ||
| KT05-3 | A4 | M40x1,5 | 3-M10 | 15 | 15 | 31 | 62 | 14 | 25 | 10 | 3-M6 | - | 30 | 53 | M8 |
| KT06-3 | A4 | M55x2 | 6-M10 | 16 | 16 | 37 | 73 | 20 | 31 | 12 | 6-M10 | 16 | 36 | 65 | M8 |
| KT06-3 | A5 | M55x2 | 6-M10 | 16 | 16 | 37 | 73 | 20 | 31 | 12 | 3-M6 | 16 | 36 | 65 | M8 |
| KT08-3 | A5 | M60x2 | 6-M12 | 20 | 17 | 38 | 95 | 25 | 35 | 14 | 6-M10 | 16 | 45 | 80 | M8 |
| KT08-3 | A6 | M60x2 | 6-M12 | 20 | 18 | 38 | 95 | 25 | 35 | 14 | 3-M6 | 16 | 45 | 80 | M8 |
| KT10-3 | A6 | M85x2 | 6-M16 | 22 | 18 | 43 | 110 | 30 | 40 | 16 | 6-M12 | 16 | 60 | 102 | M10 |
| KT10-3 | A8 | M85x2 | 6-M16 | 22 | 24 | 43 | 110 | 30 | 40 | 16 | 3-M8 | 16 | 60 | 102 | M10 |
| KT12-3 | A8 | M100x2 | 6-M16 | 23 | 25 | 51 | 130 | 30 | 50 | 21 | 3-M8 | 20 | 60 | 115 | M10 |
| KT15-3 | A8 | M130x2 | 6-M20 | 30 | 24 | 63 | 165 | 43 | 62 | 22 | 6-M16 | 20 | 80 | 150 | M12 |
| KT15-3 | A11 | M130x2 | 6-M20 | 30 | 28 | 63 | 165 | 43 | 62 | 22 | 3-M10 | 20 | 80 | 150 | M12 |
| Spez | Kolbenhub mm |
Backenhub (Durchmesser) mm |
Spanndurchmesser mm |
Max. DBpull KN (kgf) |
Max. Spannkraft KN (kgf) |
Max. Geschwindigkeit min-1 (U/min) |
ICH | Gewicht kg |
Passender Zyl. M | Max. Druck MPa (kgf/cm2) | |||
| KT05-3 | A4 | 10 | 5.5 | 135 | 12 | 17.1(1750) | 35,8(3650) | 7000 | 0.02 | 6.7 | 7.5 | TK536 | 2,9(29) |
| KT06-3 | A4 | 12 | 5.5 | 168 | 15 | 21,5(2200) | 56,8(5800) | 6000 | 0.06 | 11.9 | 14.3 | TK646 | 2,8(28) |
| KT06-3 | A5 | 12 | 5.5 | 168 | 15 | 21,5(2200) | 56,8(5800) | 6000 | 0.06 | 11.9 | 13.7 | TK646 | 2,8(28) |
| KT08-3 | A5 | 16 | 7.4 | 210 | 13 | 34,3(3500) | 85,8(8750) | 5000 | 0.18 | 22.5 | 25.4 | TK852 | 2,8(28) |
| KT08-3 | A6 | 16 | 7.4 | 210 | 13 | 34,3(3500) | 85,8(8750) | 5000 | 0.18 | 22.5 | 23.6 | TK852 | 2,8(28) |
| KT10-3 | A6 | 19 | 8.8 | 254 | 31 | 42,6(4380) | 110,7(11300) | 4200 | 0.33 | 34.5 | 41.5 | TK1075 | 2,7(27) |
| KT10-3 | A8 | 19 | 8.8 | 254 | 31 | 42,6(4380) | 110,7(11300) | 4200 | 0.33 | 34.5 | 40 | TK1075 | 2,7(27) |
| KT12-3 | A8 | 23 | 10.6 | 304 | 34 | 54,9(14650) | 143,6(14650) | 3300 | 0.77 | 56.6 | 59.5 | TK1291 | 2,7(27) |
| KT15-3 | A8 | 23 | 10.6 | 381 | 50 | 71(7250) | 179,8(18350) | 2500 | 2.47 | 120 | 134 | TK1512 | 2.1(22) |
| KT15-3 | A11 | 23 | 10.6 | 381 | 50 | 71(7250) | 179,8(18350) | 2500 | 2.39 | 120 | 127 | TK1512 | 2.1(22) |
